How Much Oil Does A 2019 Jeep Compass Take: Capacity Guide
Reading Time: 5 minutes For a U.S.-market 2019 Jeep Compass with the 2.4L engine, the oil capacity is 5 US quarts (4.7 liters) with a new oil filter. The recommended oil is SAE 0W-20 that meets FCA material standard MS-6395. Check the dipstick after filling; the stated capacity is a guide, not a reason to pour in oil past the full mark.
2019 Jeep Compass oil capacity
The 2019 Compass sold in the United States uses a 2.4L four-cylinder engine. Its specified engine-oil capacity is 5 US quarts (4.7 liters) when the oil filter is changed, as listed in the 2019 Jeep Compass Owner’s Manual, under Fluids and Capacities.
| Item | Specification |
|---|---|
| Engine in U.S.-market models | 2.4L four-cylinder |
| Oil capacity with filter | 5 US qt (4.7 L) |
| Recommended viscosity | SAE 0W-20 |
| Required oil standard | FCA MS-6395 |
The fill amount can vary slightly during a real oil change. Some old oil may remain in the engine, so use the dipstick to confirm the final level rather than assuming the engine needs exactly 5 quarts.
This capacity is for engine oil, not transmission fluid or another vehicle fluid. If your Compass was built for a market outside the United States, check its owner’s manual or confirm the engine by VIN; specifications can vary by market.
What oil does a 2019 Jeep Compass use?
Use SAE 0W-20 engine oil that meets FCA MS-6395. The owner’s manual identifies the viscosity and specification; match both when choosing oil. A bottle that says only “0W-20” may not show whether it meets the required standard.
You can check the oil container label for the required specification. The American Petroleum Institute’s oil guidance explains oil labels and service categories, but the Jeep manual’s FCA MS-6395 requirement is the key fitment detail for this vehicle.
Do not choose a different viscosity just because it is on hand. If the correct oil is unavailable, check the manual or ask a qualified service professional before using an alternative.
How to check and add engine oil
Park on level ground, switch off the engine, and let the oil settle before checking the dipstick. For the procedure that applies to your vehicle, use the owner’s manual; it describes how to read the dipstick and where the level should sit.
- Open the hood and locate the engine-oil dipstick.
- Pull it out and wipe it clean with a lint-free cloth.
- Push it fully back in, then remove it again to read the level.
- If the oil is below the safe range, add a small amount of SAE 0W-20 that meets FCA MS-6395.
- Wait briefly, then check the dipstick again. Repeat as needed, keeping the level within the marked range.
Add oil in small steps rather than pouring in a full quart at once. If the level is already at or near the full mark, do not add more; overfilling can harm the engine.
Changing the oil: practical steps
If you change the oil yourself, use the correct oil and a new filter, and work only when the vehicle is secure. A hot engine, an unstable jack, or oil spilled on the floor can cause injury.
- Park on a level surface, set the parking brake, and let the engine cool enough to work safely.
- Raise the vehicle only with suitable equipment and support it with jack stands. Never work beneath a vehicle held up only by a jack.
- Drain the old oil into a suitable pan, then replace the drain plug and oil filter as directed by the service information.
- Add the correct oil gradually. Do not assume all 5 quarts will be needed to reach the full mark.
- Start the engine briefly and check for leaks. Turn it off, wait for the oil to settle, then check the dipstick and adjust the level if needed.
Take used oil and the old filter to an approved collection or recycling site. Do not pour used oil down a drain or onto the ground.
When to change the oil
Use the Compass’s oil-change indicator and the maintenance schedule in the owner’s manual. The manual sets a maximum interval of 10,000 miles or 12 months, whichever comes first; the oil-change indicator may call for service sooner. Driving conditions can affect when service is due, so follow the schedule that fits your use.
After an oil change, reset the oil-change indicator using the method in the manual. Resetting the reminder does not change the service interval or replace the need to use the correct oil.
FAQs
Does the 5-quart capacity include the oil filter?
Yes. The specified 5 US quarts (4.7 liters) is the capacity with a new filter. Check the dipstick after filling, since some old oil may remain in the engine after draining.
Do all U.S. 2019 Jeep Compass trims use the same oil capacity?
The U.S.-market 2019 Compass models use the 2.4L engine, so the listed capacity is 5 US quarts with a filter. If your vehicle was built for another market, verify its engine and specifications in its manual.
Can I put all 5 quarts in at once?
It is better to add oil gradually and check the dipstick. Residual oil can affect how much the engine needs after a drain, and the dipstick—not the bottle count—confirms the final level.
What should I do if I overfill the engine?
Do not keep driving with the oil level above the dipstick’s full mark. Have the excess oil removed or ask a qualified mechanic to do it; too much oil can cause engine problems.
For a U.S.-market 2019 Jeep Compass, start with the 5-quart capacity, use SAE 0W-20 meeting FCA MS-6395, and let the dipstick guide the final fill.
