Jeep Blend Door Recall: Everything You Need To Know

The blend door recall is a component of your vehicle that users probably don’t give much thought to. The blend door, which functions as the car’s air conditioner, is controlled by the recall. 

So what are the signs of a defective jeep blend door recall? It includes dashboard noises, knocking, and erratic airflow. But you’ll have to do some testing, like adjusting the blend door’s calibration and inspecting the malfunctioning relay to identify the problem precisely. 

Normally, drivers rarely encounter the recall for the malfunctioning blend door, so they ignore it usually until the constant noise becomes annoying. In this article, we are going to dive into the problems of a jeep blend door recall and also how to fix them. So if you are facing this problem, this article is for you.

What is a Blend Door Recall?

The blend door recall regulates the car’s HVAC system. As you tweak the climate control, the recall for the blend door will react accordingly. For example, if you set the thermostat to a lower temperature, the blend door recall will route more chilly air to that particular vent. 

When the thermostat is set to off, the blend door recall diverts air away from the furnace. Vehicles with dual or even three climatic zones may have more than one recall for the blend door, whereas some automobiles only have one.

It also serves an essential function. The signals are transmitted through blend door recall when the dial is turned to raise or reduce the airflow. The defrosters or other air movers are also under its command.

If you have the latest model automobile, it may also be affected by a two-blend door recall. A vehicle has two recalls for the blend doors if the rear seat passengers can adjust the air conditioning and temperature volume.

What Are the Warnings of a Defective Jeep Blend Door Recall?  

There will be warning signs to look out for when your blend door starts having issues. We have laid out all the signs you need to know when your blend door is broken and why in the section below.

Clicking

A clicking noise originating from the control panel is a red flag that suggests you may have a problem with the blend door recall. It may be audible or inaudible, but relentless and repetitive. 

The dashboard area where the temperature and ventilation settings are located is the likely origin of the noise. Make an appointment with an expert immediately if you hear a clicking sound.

Knocking

The majority of the time, knocking sounds are caused by a faulty blend door recall. If you hear a knocking noise whenever you turn on your air conditioning or automobile, you need to have your blend door replaced.

Any Other Weird Noises

Also, if you hear any additional sounds from the dashboard, it could be that your blend door recall is malfunctioning. A droning or creaking noise originating from the middle of the dashboard usually indicates a problem with the blend door. 

When you adjust the thermostat or switch on the air conditioner, you’ll likely hear an increase in these noises. 

Disrupted Temperature Patterns

The mixed door recall may malfunction if the air flowing out of the vents in your car fluctuates in temperature from hot to cold without you touching the controls.

Poor Air Stability 

When the airflow from the vents is inconsistent, check the blend door recall to see if it helps. It can happen because the blend door is slamming and unlocking and the air is being redirected haphazardly, leading to erratic airflow.

Unsuitable Temperature

Getting the incorrect temperature is possible if the blend door recall is failed. In a regular situation, you can try blasting air and have it come out cold or hot as you like. You may require a fresh blend door recall if you turn the air conditioner on full blast but get hot air instead, even after letting the car warm up for a while.

When you are sure that your Jeep is experiencing the aforementioned symptoms, you will need to do certain diagnostic tests to find and cure the problem. If the techniques work, it may not be necessary to replace the entire recall.

How to Fix the Blend Door’s Alignment

Improper Diagnosis of a Relay

As was already said, strange sounds and the failure of the blend door recall mechanism are often caused by a broken relay.

Simply said, a relay is an electronic component that allows you to open and close the blend door of your Jeep automatically. Relay switches are responsible for transmitting electric signals to the blend door, and those signals are lost when they become dusty or malfunctioning.

When a relay is broken, it makes a humming sound because it can’t properly detach or connect with the contact points. Consequently, a working recall can be restored by locating a faulty relay and replacing it.

Can You Get Behind the Wheel with a Defective Jeep Blend Door?

The only real downside to driving a jeep with a broken composite door recall is the discomfort it causes. Driving safely is not affected in any way.

If nothing could go wrong with the engine, you may take your jeep out for a spin. You undoubtedly know that a blend door recall allows you to adjust the air conditioning in your vehicle to your preferred temperature. 

So you may feel some pain because you can’t control the temperature when you have a defective Jeep blend door. In this case, you can easily open the windows whenever they’re needed. 

Replacement of Blend Door Recall

Replacement of the recalled blend door is not required at any specific interval. It has been documented that certain automobiles’ mixed doors eventually stop functioning, while others may continue to function for quite some time. 

If your blend door shows signs of the recalled defect, you should think about replacing it. There are many blending doors recalls that might be expected to endure the lifetime of the car.

Blend door recall replacement requires careful attention to detail while selecting the correct components for your particular vehicle. Refer to the handbook whenever you are unsure of something.

What Exactly Does the Free Blend Door Replacement Recall Include?

Blend door recall failures require recalibration or replacement. To control the airflow inside of your vehicle, a blend door is used. The recall can adjust the amount of airflow into the vehicle by opening and closing this flap. 

Recall replacement may be required if doors become stuck in open or closed positions. Additionally, the recall’s gear teeth regularly wear out or crack, leading to an annoying clicking noise whenever the air conditioner or heater is adjusted.

You can choose to replace the gearbox, the door, or anything that needs to be recalled. Replacement of a recalled mix door will follow the same procedure as any other recalled vehicle components. 

In most cases, this entails removing the dashboard, removing any relevant recall, and replacing the dashboard. The wire harnesses or vacuum tubes that operate the new recalls must also be attached.

Accordingly, blend door recall repairs should always use genuine Original Equipment Manufacturer components. Although aftermarket components could save you money, they may not provide a perfect match for your car. 

Moreover, a recalled mix door replacement shouldn’t take longer than one hour to accomplish.