If your Jeep Renegade’s license plate bulb burns out or is broken, replace it sooner rather than later. The license plate bulb must be illuminated at night so that law enforcement can identify your vehicle.
But how to change the jeep Renegade license plate bulb? Use a screwdriver or a butter knife to snap the bulb housing from its left side. Snap the socket from the connector. Once the unit is out, rotate the bulb holder and remove the tag bulb. Replace it and reverse the steps.
That’s the summary of the steps to change the license plate bulb in your Renegade. Everything you need to know about this process in detail is discussed downward.
Table of Contents
How To Change Jeep Renegade License Plate Bulbs?
Changing a Jeep Renegade license plate bulb is a relatively easy task that any car owner can do in no time. Here’s what you need to do.
Step 1: Get The Necessary Tools
The first step is to gather the necessary tools to perform the job. You will need a small flathead screwdriver, a butter knife or something sharp and flat, and your thumb to disconnect the connector.
Step 2: Remove The Old Bulb
The next step is to remove the old bulb. Start by inserting the flathead screwdriver or butter knife through the left side of the license plate bulb housing. Here you’re pushing a metal spring back to release the housing.
Once it’s out, use your thumb to disconnect the black connector and pull the bulb assembly out.
With the entire housing out, you need to remove the bulb holder. Gently rotate the bulb socket counterclockwise to remove it from the housing. Once you have the holder free, simply pull the old bulb out and discard it.
Step 3: Replace The Bulb
Take your new bulb and insert it into the holder. Insert the socket into the housing, ensuring that the two tabs are lined up with the holes. When it’s in place, twist it to lock it in place.
Step 4: Reattach The Assembly
Once the new bulb is in place, reconnect the connector and make sure to push the tab in securely. Then, push the housing up, and it will lock into place. It’s important to note that when attaching the bulb housing, you should push the bulb in securely to avoid it popping out.
Step 5: Test The Bulb
The final step is to test the bulb to ensure it works properly. Turn on the headlights of your Jeep and check the license plate area to ensure the bulb is lighting up. If it isn’t, you may need to adjust the bulb or reattach the housing to ensure it’s in the correct position.
Check if the warning light comes on in the dashboard. The car computer will show a warning light if the build is dead or disconnected or if you use the wrong tag bulb.
Why Is It Important To Change Your Jeep Renegade License Plate Bulb?
You don’t want to overlook your Jeep Renegade license plate bulb. Some people think this small light is not important or necessary, but it serves an essential function.
This bulb helps illuminate your vehicle’s license plate, allowing law enforcement to identify and track your car easily. If your license plate bulb is not functioning properly, it can lead to costly fines or penalties.
That’s why you want to ensure your Jeep Renegade license plate bulb is bright and working correctly. Over time, this bulb can become burned out or damaged due to oxidation and seal failure.
If the light goes off completely, your car’s computer may detect a problem and send you a warning message.
You can check your license plate light bulb by applying the emergency brake and turning on your car’s ignition. Then, walk around your vehicle to see if the light is working properly. If it is not, you may need to replace your Jeep Renegade license plate bulb.
When Should You Change Your Jeep Renegade License Plate Light Bulb?
You should regularly check your Jeep Renegade license plate bulb to ensure it works properly. You should change your tag bulb if you notice any of the following signs:
- The light is dim or not illuminating at all. This could indicate a burnt-out or faulty bulb that needs to be replaced.
- The light flickers or flashes on and off. This could signify a loose or damaged connection that needs to be fixed.
- The light appears to have a yellow or orange tint. This could indicate that the bulb has reached the end of its lifespan and needs to be replaced.
- The light is not working on one or both sides of the vehicle. This could signify a faulty bulb or a problem with the wiring or electrical system.
In general, changing your Jeep Renegade license plate light bulb is recommended every 12-18 months. This will ensure that it is functioning correctly and providing adequate visibility for other drivers on the road.
It is also essential to check the bulb regularly and replace it as soon as you notice any issues to avoid potential safety hazards.
How Much Does It Cost To Replace A Jeep Renegade License Plate Bulb?
| Bulb Type | Cost | Labor |
| Basic | $5-$10 | $50-$120 |
| LED | $6-$70 | $50-$120 |
| Fog Light | $5-$20 | $50-$120 |
The cost of replacing a Jeep Renegade license plate bulb can vary depending on several factors. One major factor is the type and quality of the bulb you choose, as different bulbs may have different price tags.
Other factors include your vehicle type, the labor costs in your area, and any additional fees for parts or services.
On average, replacing a Jeep Renegade license plate bulb is typically anywhere from $5 to $50. Your total cost may be higher if you replace it with a professional mechanic or dealership.
Averagely, you will pay $90 for the build installation labor depending on the city and shop you go to.
If you are comfortable doing the work yourself, you can save significant money on the replacement cost.
Bottom Line
Replacing a Jeep Renegade license plate bulb is a straightforward process. With the right tools and a little bit of know-how, you can easily change out your tag bulb in no time.
Always use the correct type of license plate bulb for your vehicle to avoid potential safety hazards. Additionally, it is highly recommended to regularly check your license plate bulb and replace it as soon as you notice any issues.
