How to Reset Tire Pressure Light on Jeep Cherokee: Quick & Easy Guide
Reading Time: 7 minutes If you’re seeing the tire pressure light on your Jeep Cherokee dashboard, it can be frustrating and confusing. You might wonder, “How do I turn this light off without a trip to the mechanic?” The good news is, you can reset the tire pressure light yourself quickly and easily.
This guide will walk you through simple steps to find the reset button, check your tire pressures, and get your Jeep’s system back on track. Keep reading, and you’ll learn exactly what to do so that warning light stops distracting you on the road.
Your Jeep deserves the best care—and you deserve peace of mind.
Locate Tpms Reset Button
Locating the TPMS reset button in your Jeep Cherokee is the first step to turn off the tire pressure light. This button helps the system relearn the correct tire pressures after adjustment. Finding it might take a moment as its location varies slightly by model year.
Knowing exactly where to look saves time and avoids frustration. Usually, the button is easy to spot near the driver’s seat area. Below are common places to check.
Check Left Of Steering Wheel
Start by looking under the dashboard, left of the steering wheel. This area often holds small buttons for vehicle controls. The TPMS reset button shows a tire icon with an exclamation mark inside.
It might be on a panel or near the hood release lever. Press and hold this button until the tire light blinks. This signals the system is resetting.
Inspect Glove Box
If you do not see the reset button left of the steering wheel, open the glove box next. Some Jeep Cherokee models place the button inside the glove compartment. It could be near the fuse box or along the edges.
Look carefully for the small tire-shaped icon. Pressing this button also starts the TPMS reset process. Remember to have all tires properly inflated before pressing.
Credit: www.youtube.com
Prepare Tires
Preparing your tires is the first step to reset the tire pressure light on your Jeep Cherokee. Proper tire preparation ensures the sensor reads the correct pressure.
Check each tire carefully for air pressure. Low pressure can cause the warning light to stay on.
Inflate To Recommended Pressure
Locate the recommended tire pressure on the driver’s door jamb sticker. Use a reliable tire pressure gauge to check each tire. Inflate tires to match the recommended PSI exactly. Do not overinflate or underinflate. Correct pressure helps the TPMS function properly.
Include Spare Tire
Some Jeep Cherokee models monitor the spare tire pressure. Check the spare tire and inflate it to the recommended level. A low spare tire can also trigger the pressure warning light. Keep the spare ready for emergencies and sensor accuracy.
Reset Tire Pressure Light
The tire pressure light on your Jeep Cherokee signals low tire pressure or a system alert. Resetting this light helps ensure your vehicle’s safety and efficiency. Follow these simple steps to reset the tire pressure light and keep your Jeep running smoothly.
Turn Ignition To On
Insert your key and turn the ignition to the “ON” position. Do not start the engine. This powers the vehicle’s electrical system and prepares the TPMS for reset.
Press And Hold Reset Button
Locate the TPMS reset button, usually found under the steering wheel or inside the glove box. Press and hold this button firmly for a few seconds until the light begins to respond.
Wait For Light To Blink
Watch the dashboard for the tire pressure light to blink three times. This blinking confirms the reset process has started. After this, release the reset button and start driving to recalibrate the system.
Credit: www.firkins.com
Drive To Recalibrate
After pressing the TPMS reset button in your Jeep Cherokee, driving helps the system recalibrate. This step lets the sensors adjust to the correct tire pressure. The tire pressure light will turn off once the system confirms proper pressure levels. Driving also helps the sensors detect any changes in tire pressure accurately.
Recommended Driving Conditions
Drive on smooth, flat roads for best results. Avoid rough or uneven surfaces that may affect sensor readings. Keep a steady speed without sudden stops or sharp turns. Daylight driving is better as sensors work optimally in normal temperatures. Make sure the tires are properly inflated before you start driving.
How Long To Drive
Drive for about 10 to 15 minutes to allow full recalibration. Maintain a speed of 30 to 50 miles per hour during this time. Short trips or slow speeds might not reset the light. After driving, check if the tire pressure light turns off. If it stays on, repeat the driving step or consult a mechanic.
Troubleshoot Persistent Light
The tire pressure light on your Jeep Cherokee may stay on after resetting. This persistent light can signal a deeper issue. Troubleshooting helps find the real cause. This section explains how to check and fix common problems that keep the light on.
Check For Faulty Sensors
The tire pressure sensors can fail over time. Dirt, damage, or battery issues cause sensor failure. Inspect each tire sensor carefully. Look for physical damage or dirt buildup. Clean the sensors gently if needed. Replace any sensor that shows signs of damage or does not work properly.
Faulty sensors send wrong signals to your vehicle’s system. This causes the tire pressure light to remain on. Checking sensors first can save time and money.
Use Diagnostic Scan Tool
A diagnostic scan tool reads the car’s error codes. It connects to the Jeep Cherokee’s computer system. This tool identifies exact sensor problems or other issues. Use it to find hidden faults causing the light to stay on.
Many auto shops offer scanning services. Some tools are affordable and simple to use at home. The scan tool helps reset the system after repairs. This ensures the tire pressure light turns off correctly.
Prevent Future Tpms Issues
Preventing future issues with your Jeep Cherokee’s Tire Pressure Monitoring System (TPMS) saves time and money. Simple care steps help keep sensors accurate and reliable. This section covers key habits to avoid TPMS warnings and sensor failures.
Regular Tire Maintenance
Check tire pressure at least once a month. Use a reliable tire pressure gauge for accuracy. Inflate tires to the recommended pressure on the door jamb sticker. Rotate tires every 5,000 to 7,000 miles to ensure even wear. Inspect tires for damage, such as cuts or punctures. Replace worn tires promptly to keep sensors working correctly.
Sensor Battery Care
TPMS sensors run on small batteries that last 5 to 10 years. Replace sensors when batteries die to avoid false alerts. Have a mechanic check sensor batteries during tire service. Avoid damaging sensors during tire changes or repairs. Use professional tools to handle sensors carefully. Proper care extends sensor life and keeps the system accurate.
Credit: www.youtube.com
Frequently Asked Questions
Where Is The Tpms Reset Button On A Jeep Cherokee?
The Jeep Cherokee TPMS reset button usually sits under the steering wheel, left of the column, or inside the glove box. Press and hold it until the tire light blinks three times to reset after inflating tires properly.
How Do You Reset The Tire Pressure Light On A 2019 Jeep Cherokee?
Check all tires for correct pressure per door jamb sticker. Turn ignition to “ON” without starting. Press and hold the TPMS reset button until the light blinks three times. Release the button, then drive to complete recalibration.
How To Reset Tire Pressure On 2015 Jeep Cherokee?
Inflate all tires to the recommended pressure. Turn ignition to “ON” without starting. Press and hold the TPMS reset button until the light blinks three times. Release the button and drive for a few minutes to recalibrate the system.
Why Is My Tire Pressure Light Still On After Filling Tires On My Jeep?
Your Jeep’s tire pressure light stays on if the TPMS hasn’t reset. Press the reset button under the steering wheel, then drive to recalibrate. A faulty sensor or dead battery may also cause the light to remain on, requiring professional diagnosis.
Conclusion
Resetting the tire pressure light on your Jeep Cherokee is simple. First, check all tires for correct pressure. Locate and hold the TPMS reset button until the light blinks. Then, drive for a few minutes to complete the reset. This process keeps your vehicle safe and running smoothly.
If the light keeps flashing, a sensor may need professional attention. Regular tire checks help prevent issues and save you money. Follow these easy steps to keep your Jeep in top shape.
