It is generally more difficult to locate your tools in a large vehicle such as the Jeep Wrangler. However, it is critical to know the exact location of tools like the jack, so that you can readily reach it in case of an emergency.
So, where is jack located on Jeep Wrangler? Usually, it can be found in the back of the vehicle, in the cargo area. Moreover, to access the jack, you will need to remove a panel in the cargo area, which is typically secured with several screws.
In this article, we’re going to have an in-depth view of how to use this tool properly and its location on Wrangler. So let’s dig in!
Table of Contents
Where Is Jack Located On Jeep Wrangler?
One of the most popular accessories of the Jeep Wrangler is the Jack. The jack is used to lift the vehicle when changing a tire or performing routine maintenance. But where is it located on your Jeep Wrangler? Well, it varies based on the models.Â
Location 1: The Cargo Area
The Jack is located in the rear cargo area of the Jeep Wrangler‘s recent models, such as the JK. It is secured to the cargo area’s floor with two bolts and can be easily accessed when needed.Â
Location 2: Underneath the Wrangler
For older model years of the Jeep Wrangler, such as the TJ and YJ, a jack is typically located underneath the vehicle near the left rear wheel. It is easy to access and should be included with the vehicle when it is purchased.
How to Access the Jack on Wrangler?
To access the Jack, simply open the rear cargo door and locate the two bolts that secure it to the floor. Loosen the bolts and the Jack should come loose. Make sure to keep the bolts and the Jack in a safe place so you can easily locate them when needed.
In either case, it is important to note that the jack found underneath the Jeep Wrangler is not suitable for lifting the entire vehicle. Instead, it is meant for raising the vehicle enough to change a tire or perform other minor tasks. For major repairs and maintenance, a more powerful jack should be used.
Precautions Before Using the Jack on Jeep Wrangler
The Jeep Wrangler is a highly capable off-road vehicle that requires proper use of the vehicle’s jack. Jacks are used to lifting vehicles off the ground and are necessary for certain maintenance tasks, such as changing a tire or performing under-carriage repairs.
Unfortunately, improper use of a jack can lead to serious injury and damage to the vehicle. Therefore, you must take proper precautions and follow the manufacturer’s instructions for using the jack.
Here are some precautionary steps you should take before lifting your Wrangler-
Checking the surface
Before beginning any work, make sure the vehicle is parked on a flat, level surface and the parking brake is engaged.
Additionally, check the ground where the jack will be placed to make sure there are no jagged rocks or obstructions that could damage the jack or the vehicle. If you are unsure whether the ground is level, use a level to check.
Positioning the jack in the correct manner
When positioning the jack, ensure it is placed in the correct area for the vehicle’s model and year. The owner’s manual should specify the location. The jack should also be positioned in the center of the vehicle, so the load is evenly distributed on both sides.
Finally, the jack should be placed on the vehicle’s frame, never on the body or suspension parts.
Don’t operate manually
Once the jack is in place, slowly raise the vehicle using the jack’s handle or pump. Do not use the jack’s handle or pump to lower the vehicle. Instead, use the jack’s release valve to slowly lower the vehicle. Never attempt to lower the vehicle by manually pushing or pulling the jack.
Look out for signs of instability
When the vehicle is in the air, make sure the jack is securely supporting the vehicle. Check for any signs of instability, such as rocking, wobbling, or tipping. If the jack is not adequately supporting the vehicle, lower the vehicle and readjust the jack.
Checking the condition of the jack
Additionally, never stand under the vehicle while it is on the jack. Instead, place jack stands under the vehicle for extra support. After the vehicle is lowered, check the jack for signs of damage or wear. If the jack is damaged or worn, replace it immediately.
By following these precautions and the manufacturer’s instructions, Jeep Wrangler owners can ensure they use their jacks safely and prevent serious injury or damage to their vehicles.
How To Jack The Jeep Wrangler Properly?
If you’re considering a Jeep Wrangler, you’ll need to know how to use a jack to ensure your vehicle is safe and secure. Jacks are essential for lifting the vehicle off the ground when changing tires, oil, or performing other maintenance.Â
Here’s a step-by-step guide on how to use a jack on a Jeep Wrangler.
Step 1: Position the Jack
Start by parking your Jeep Wrangler on a smooth, flat surface. This will help ensure the jack is stable and will prevent any accidents. Place the jack on the ground and position it so that it is centered on the axle. It will need to be located directly beneath the lift point.
Step 2: Lift the Vehicle
Once the jack is in the correct position, use the handle to lift the vehicle. Most Jeep Wranglers’ lift point is located on the rear differential. As you lift the vehicle, it’s important to keep an eye on the jack and make sure it stays where you placed it. If it starts to shift, stop and readjust it before continuing.
Step 3: Secure the Vehicle
Once the vehicle is lifted, it’s important to secure it. This can be done by placing chocks around the tires to prevent them from rolling. You should also set the parking brake to ensure the vehicle stays in place.
Step 4: Perform Maintenance
Once the vehicle is secure, you can begin performing maintenance. This could include changing the tire, and oil, or checking other components. Make sure to double-check all nuts and bolts before lowering the vehicle.
Step 5: Lower the Vehicle
Once you’re finished with the maintenance, it’s time to lower the vehicle. To do this, simply reverse the process you used to lift it. Start by releasing the parking brake and removing the chocks. Then, use the release valve to lower the vehicle to the ground.
Using a jack on a Jeep Wrangler is a fairly simple process. Just make sure to follow all safety precautions and double-check that the vehicle is secure before performing any maintenance. With the proper care and attention, you can ensure that your vehicle remains safe and secure.
Bottom Line
Now you know where is jack located on Jeep Wrangler. You can use it for repair, maintenance, or just for regular checkups of your Wrangler. As the jack comes with factory settings in Wranglers, you can be worry-free about its quality.
However, it is important to note that Jack should always be used with extreme caution. It should never be used to lift the vehicle while someone is underneath. Additionally, the Jack should always be securely fastened to the vehicle before being used.