Jeep Renegade Ignition Coil & Spark Plugs

Jeep Renegade Ignition Coil & Spark Plugs: 1.4T & 2.4 Guide

Replacing the ignition coils and spark plugs on a U.S.-spec Jeep Renegade is a practical repair for many home mechanics. The 1.4L MultiAir Turbo and 2.4L Tigershark engines use coil-on-plug ignition, so each spark plug has an ignition coil mounted above it.

The basic job is the same on both engines: remove the engine cover if fitted, disconnect each coil, remove the coil fastener, clean the spark plug well, replace the plug, and reinstall the coil. Allow the engine to cool fully, use parts matched to the vehicle identification number (VIN), and follow the factory torque and spark plug gap specifications for the exact model year.

Tools and parts you need
Source: innova.com

Tools and parts you need

Gather the correct tools before you begin. A clean work area helps prevent dirt from entering the spark plug wells or intake system.

Tools

  • Ratchet
  • Extension bars
  • Torque wrench
  • Thin-wall spark plug socket, usually 5/8 inch or 16 mm
  • Small socket set
  • Trim tool or flat screwdriver
  • Compressed air or a clean air blower
  • Dielectric grease
  • Work light
  • Clean shop towels

Replacement parts

  • Correct spark plugs for the engine and VIN
  • Replacement ignition coil or coils, if testing confirms a coil fault
  • New coil fasteners if the service information calls for them
  • New intake duct clamps or seals if they are damaged

The correct plug can vary by engine, model year, emissions package, and replacement-part catalog. Do not select a plug only because it fits the thread. Check the owner’s manual, factory service information, or a reputable parts catalog using the VIN.

The same rule applies to ignition coils. A coil listed for a different Jeep, Fiat, or Chrysler engine may look similar but have a different connector, boot length, electrical range, or mounting design.

Safety steps before starting

Work only on a cold engine. Spark plugs sit in the cylinder head, and removing them from a hot aluminum head can damage the threads.

Park the Renegade on level ground, select Park, set the parking brake, and switch off all electrical accessories. Open the hood and keep the key away from the vehicle if it uses keyless entry.

Disconnecting the negative battery cable is a cautious step when working around electrical connectors. If you disconnect it, record any radio or vehicle settings that may need to be restored. Make sure the cable cannot touch the battery terminal while you work.

Do not pull on ignition coil wires. The Renegade uses electrical connectors, and damaged connector locks can cause an intermittent misfire. Do not use metal tools to pry hard against the plastic coil housing.

How to replace spark plugs and ignition coils

The 1.4L turbo and 2.4L engines use a similar replacement method, but access around the top of the engine differs. The 1.4L turbo may have intake or charge-air parts near the ignition coils. Remove only the parts needed for access, and mark hose locations before disconnecting them.

1. Confirm the failed cylinder

If the check engine light is on, scan the vehicle before removing parts. Codes such as P0301, P0302, P0303, and P0304 identify a cylinder-specific misfire. A code such as P0300 indicates random or multiple-cylinder misfires.

A misfire code does not prove that the ignition coil is bad. A worn plug, fuel injector problem, vacuum leak, low compression, or wiring fault can create the same symptom.

If the scan tool identifies one cylinder, compare its coil with a coil from another cylinder when practical. Clear the code, run the engine, and see whether the misfire moves to the other cylinder. If the misfire follows the coil, the coil is a strong suspect. If it stays on the same cylinder, inspect the plug and look for fuel, air, compression, or wiring problems.

2. Remove the engine cover and intake parts

Remove the plastic engine cover if the vehicle has one. Most covers lift from rubber mounts, but some use fasteners. Pull straight up only after checking for bolts or clips.

On the 1.4L MultiAir Turbo, an air duct, resonator, or other intake part may limit access. Loosen the required clamps and release the duct without forcing it. Cover open intake tubes with a clean towel so debris cannot enter.

On the 2.4L Tigershark, access is usually more direct, but the exact layout depends on the model year and equipment. Take a quick photo before removing hoses or electrical connectors.

3. Disconnect the ignition coil

Press the connector lock and slide the electrical connector off the coil. Some locks must be released with a small trim tool. Use light pressure and work the lock rather than pulling the wires.

Remove the coil retaining bolt or fastener. Place each fastener in a tray so it does not fall into the engine bay.

Twist the coil boot gently while lifting it from the spark plug. If it will not move, check for a hidden fastener or stuck rubber boot. Do not use excessive force against the coil body.

4. Clean the spark plug area

Use compressed air around the coil opening before removing the spark plug. Dirt, sand, and leaves can fall into the cylinder when the plug is removed.

Keep the air nozzle a short distance from the engine and wear eye protection. If you do not have compressed air, use a clean brush and vacuum carefully. Do not push debris down the plug well.

5. Remove the old spark plug

Fit the spark plug socket fully onto the plug. Turn it counterclockwise with a ratchet and extension.

If the plug feels stuck, do not jerk the ratchet. Apply steady pressure and stop if the socket begins to slip. Cross-threading or damaging the cylinder head can turn a routine plug change into a costly repair.

Lift the old plug out and inspect it. A normal plug often has light tan or gray deposits. Heavy black carbon, wet fuel, oil on the firing end, a cracked insulator, or a melted electrode can point to a problem beyond normal wear.

Oil around the outside of the plug may indicate a valve cover or tube-seal leak. Oil on the firing end may point to an internal engine issue. The location of the oil matters.

6. Check the new plug

Compare the new plug with the old one before installation. Confirm the thread length, seat style, terminal, and insulator shape.

Check the gap against the exact Jeep service specification. Do not assume all plugs for the 1.4L or all plugs for the 2.4L use the same gap. Pre-gapped plugs can be moved during shipping, and iridium or platinum center electrodes can be damaged by careless adjustment.

Use a wire-style or proper plug-gap gauge. Avoid prying against the fine center electrode. If the gap is wrong and the plug cannot be adjusted safely, replace the plug.

Do not apply anti-seize unless the plug manufacturer or Jeep service information specifically permits it. Many modern plated spark plugs are designed for dry installation. Anti-seize can alter tightening torque and lead to over-tightening.

7. Install the new spark plug

Place the new plug into the spark plug socket. Lower it straight into the well.

Start the plug by hand using the extension only. Turn it several full rotations without a ratchet. If it does not turn smoothly, remove it and start again. This step protects the aluminum cylinder-head threads.

Tighten the plug with a torque wrench set to the specification for the exact engine and plug. Spark plug torque is not universal. Too little torque can allow heat transfer problems or loosening; too much can stretch the plug or damage the cylinder head.

8. Install the ignition coil

Inspect the coil boot for tears, carbon tracking, oil, or a damaged spring terminal. A thin film of dielectric grease inside the boot can help prevent moisture from sticking the rubber to the plug, but do not fill the connector with grease or coat the metal terminal excessively.

Push the coil straight down until it seats firmly on the spark plug. Reinstall the coil retaining fastener and tighten it to the vehicle’s specified torque.

Reconnect the electrical connector until its lock clicks or fully engages. Gently tug the connector to confirm that it is secure.

9. Repeat the process

Replace the remaining spark plugs one cylinder at a time. Keeping the other coils installed reduces the chance of mixing parts or dropping debris into open plug wells.

If you are replacing only one ignition coil, install it in the cylinder identified by testing. Replacing all coils is not always necessary unless the service history, inspection, or diagnostic results support that decision.

10. Reinstall removed parts

Reinstall the engine cover, intake duct, resonator, brackets, and any electrical clips. Make sure every hose clamp is tight and every connector is locked.

Remove tools and towels from the engine bay. Reconnect the negative battery cable if you disconnected it.

Safety steps before starting
Source: innova.com

Engine-specific differences: 1.4T versus 2.4L

The procedure is broadly alike, but the two Renegade engines have different access and service details.

Feature 1.4L MultiAir Turbo 2.4L Tigershark
Ignition design Coil-on-plug Coil-on-plug
Common access issue Intake and turbo plumbing may limit room Engine-cover and upper-engine access may vary
Plug choice Must match the turbocharged 1.4L application Must match the naturally aspirated 2.4L application
Diagnostic concern Misfires can affect turbo operation and catalyst temperature Misfires can cause rough running and catalyst damage
Specification priority Use the exact VIN-based plug gap and torque Use the exact VIN-based plug gap and torque

Do not transfer the 1.4L plug specification to the 2.4L engine. The engines use different combustion chambers, heat ranges, ignition requirements, and factory calibration.

The 1.4L turbo may also require more care around intake hoses and charge-air connections. A loose hose can create a boost leak or lean-running fault after the plug job.

The 2.4L may offer more room around the coils, but that does not remove the need for clean plug wells and correct torque. Aluminum cylinder-head threads can still be damaged by cross-threading or over-tightening.

How to diagnose a misfire after the repair

Start the engine and let it idle. It may take a few seconds for the computer to relearn idle quality after battery power has been removed.

A successful repair should produce a smooth idle, normal throttle response, and no flashing check engine light. Some stored codes may remain until they are cleared with a scan tool or until the vehicle completes enough drive cycles.

If the engine still misfires, use this order:

  1. Confirm that each coil connector is fully locked.
  2. Check that each coil is seated on the spark plug.
  3. Inspect for a cracked plug or incorrect gap.
  4. Check that the intake duct and hoses are sealed.
  5. Scan for current and pending trouble codes.
  6. Swap the suspected coil with another cylinder.
  7. Inspect injector operation, wiring, and compression if the misfire does not move.

A flashing check engine light usually means the engine is misfiring badly enough to threaten the catalytic converter. Reduce load and stop driving unless moving the vehicle to a safe place or repair facility. Do not continue driving for days while the light flashes.

If oil or coolant is found in a plug well, fix the leak before installing another coil. Fluid can damage the boot and create a repeat failure.

Common mistakes to avoid

Installing the wrong spark plug

A plug can have the correct diameter and still be wrong for the engine. Check heat range, reach, seat type, electrode design, and gap.

Using a universal torque value

Spark plug and coil fastener torque depends on the engine, fastener, plug design, and service information. Use the specification for the exact Renegade application.

Dropping debris into the cylinder

Always clean around the plug before removal. Small grit can damage the cylinder wall or valve seat.

Forcing a plug with a ratchet

Start the plug by hand. If the threads feel rough, stop and inspect them. A cross-threaded plug can damage the cylinder head.

Replacing coils without testing

A misfire code identifies a cylinder, not always the failed part. Test the coil, plug, wiring, injector, and compression as needed.

Leaving the intake system loose

A loose clamp or disconnected hose can cause a new check engine light. Inspect every intake connection before starting the vehicle.

How to replace spark plugs and ignition coils
Source: ebay.com

When should you replace the coils and spark plugs?

Replace spark plugs at the interval listed for the specific Renegade engine and model year. The recommended interval can change with engine design, plug type, driving conditions, and updated maintenance schedules.

Ignition coils do not have one universal replacement interval. Replace a coil when testing, inspection, or a repeat cylinder-specific misfire supports the diagnosis.

Consider replacing all spark plugs together when one plug is worn. A matched set gives the engine similar ignition performance across all cylinders. Replacing all coils at once is a different decision and may add cost without solving the cause of a single-cylinder fault.

The most useful evidence includes:

  • The misfire follows the coil during a swap test.
  • The coil has visible cracks or carbon tracking.
  • The coil connector or boot is damaged.
  • The same cylinder repeatedly misfires with a known-good plug.
  • Diagnostic testing rules out fuel, air, and compression faults.

Frequently asked questions

Can I replace only one spark plug?

You can replace one plug for diagnosis or an emergency repair, but replacing the full set is usually better when the plugs have similar age and wear. A full set keeps the ignition system consistent.

Do I need to replace the ignition coils when I replace the spark plugs?

No. Replace the coils only if testing or inspection shows a fault. Spark plugs are scheduled maintenance items; ignition coils usually are not.

Can a bad spark plug damage an ignition coil?

Yes. A worn, fouled, or incorrectly gapped plug can increase the voltage demand on the coil. A damaged boot, oil leak, or moisture can also cause arcing and coil failure.

Why does the Jeep still run rough after new plugs?

The cause may be a faulty coil, injector, vacuum leak, intake leak, wiring problem, low compression, or incorrect plug installation. Scan the vehicle and use a coil swap test rather than replacing parts at random.

Should I clear the check engine code after the repair?

Clearing the code can confirm whether the fault returns, but record the original code and freeze-frame data first. If the light flashes, address the misfire immediately rather than simply clearing it.

Final checklist

Before closing the hood, confirm that:

  • Every spark plug matches the VIN-based application.
  • Every plug has the correct gap.
  • Each plug was started by hand and torqued correctly.
  • Each coil is fully seated.
  • Every coil connector is locked.
  • Intake hoses and clamps are secure.
  • No tools or towels remain in the engine bay.
  • The engine starts without a flashing check engine light.
  • A scan tool shows whether any misfire code has returned.

Replacing the ignition coils and spark plugs on a Jeep Renegade 1.4T or 2.4L is manageable when access, cleanliness, parts selection, and torque are handled carefully. If the misfire remains after the ignition parts are confirmed, stop replacing parts and continue with fuel, air, wiring, and compression testing.

Author

  • Rifat Ahmed

    Rifat Ahmed is the founder and lead author of Jeep Corner, a blog for Jeep enthusiasts. With over 10 years of experience in off-roading and Jeep customization, he shares practical tips on maintenance, upgrades, and trails.

    View all posts

You may also like to read